QRSS experiments: FSKCW and Slow Hell

These last few days I've been experimenting with my QRPLabs Ultimate 2 and Ultimate 3s transmitting on 7 MHz. In addition to WSPR, the modes transmitted have been FSKCW with 6 second long dots, and Slow Hell with 17 second long characters. The result as received this morning can be seen on the display from the grabber of Les, G3VYZ in Northumberland, UK. This is a stack of 6 consecutive 10 second frames as can be found on the QRSS grabber site of AJ4VD.

FSKCW and Slow Hell reception of LA3ZA at G3VYZ

My signal is on 7,039.870 kHz and has been set up with a FSK shift of 6 Hz. Power output was 0.2 W and the distance is about 890 km.

It works but the reception is much less reliable than for WSPR, which is not so unexpected. At the same time the WSPR signal was received all around Northern Europe (G, GM, DL, ON, OE, LX, LA, OY, OH, PA, SM) as well as on the Canary Islands, 3930 km away.

FT8 anomaly or long delayed echo?

My friend Alf, LA2NTA, has sent me these screenshots from when he has been operating FT8. The first image is when operating 10 meters and took place early in November.

Two of LA2NTA CQs being received by himself on 10 meter (in red)

It shows how his own CQ comes back to him at 10.54.00 and at 11.00.00 and is decoded in his own receiver. The echoes return at the time of transmission.

Simple interference fix for the Chinese Pixie

The Chinese Pixie transceiver operating at 7023 kHz has become very popular. It often costs less than 5 USD on Ebay. Like most Pixies it is susceptible to broadcast breakthrough and intermodulation. Much of this is caused by the keying circuit of the audio amplifier, the LM386. The cure is to move the muting diode from the power supply pin (no. 6) to the bypass pin (no. 7). I have described this in another blog post with title: "Using pin 7 of the LM386 to reduce BCI and add side tone to Pixie 2".

Here are two pictures that show how this can be done for the Chinese Pixie. One needs an additional resistor in the range 10 - 51 ohms. If you can fit it, then use the large 51 ohms resistor that come with some of the kits (I think it is meant for a dummy load). I have used 10 ohms in the picture. It replaces the old R3 of 1 k. The diode D3 is not mounted in the holes provided, and instead it is mounted under the PCB with the minus (denoted by the ring) connected to where D3's minus was, and the plus side connected to pin 7 of the LM386.

R3 is indicated by the lower left arrow, and the old
placement of D3 is shown with the upper arrow

Comparing two antennas with WSPR

Ultimate 3S with 5-band relay module in front,
variable LM2596 power supply (with voltmeter) for
the power amplifier behind left,
a variable LM2596 supply set for 5 Volts for the Ultimate 3S
in the middle, and the antenna switch to the right in the back.

WSPR - The system for Weak Signal Propagation Reporter makes it easy to compare antennas if your transmitter can instantly switch antennas. The system shown here can send on antenna 1 for almost two minutes and then switch immediately to antenna 2 for the next transmission.

The Ultimate 3S already has software that supports that and application note 3 from QRPLabs (Controlling additional relays using the Ultimate3S “Aux”) describes how. I built mine following that note and the experience from EA1CDV.

The circuit is controlled from pin D7 and consists of a transistor, a relay, a resistor and an electrolytic capacitor. In addition I have two LEDs that indicate which antenna which is in use. In the first picture the green LED in the back right under the BNC antenna connector shows that antenna 1 is connected.