Propagation via aurora reflection

Northern Lights in Tromsø, Norway 

Here is a recording of the Swedish station SM6CNN in contact with me on 29. October 2003, 22:42 UTC on 28.024 MHz. The direct distance is about 275 km.

Note the noise-like signal which is typical for signals that have been reflected off the aurora on the higher HF and on VHF frequencies. There was a strong geomagnetic disturbance that day with the K-index at Dombås, Norway reaching a value of 9 which explains the occurrence of aurora reflection.

Polar flutter

Arctic areas

Here is a recording of JW/DJ3KR on Spitzbergen from 24. August 2007, at about 21:45 UTC. This was only a few minutes after I had contact with him on 7.002 MHz.

Notice the fluttery character of his signal. On this day it wasn’t too bad and it wasn’t too hard to copy his signal, but on other occasions, signals that travel over the polar zone may be impossible to copy correctly. The K-index in Tromsø, which lies between Oslo (60 deg. N) and Spitzbergen (78 deg. N), at the time was 0.

[Image source: regjeringen.no]

Moonbounced echoes on 6792.5 and 7407.5 kHz

Recently, a facility with big enough antenna (300 by 365 m) and high enough power (3.6 MW) was used to set a new record for how low in frequency one can go and still get echoes from the moon.

This was also done during the HAARP moonbounce experiment which encouraged radio amateurs to listen on 19 and 20 January 2008. At my location in Oslo, I only heard the direct signal from Alaska, but many in the US heard good moon echoes.

K2 Fixed Level Audio Output

I started by making a very simple modification for a low level audio output with level that was independent of the AF pot setting.

The next step was to modify my front panel board by adding an audio output (mic plug) via a 25 x audio buffer and a zero-beat indicator which uses the same signal. The added circuit is built Manhattan-style on the upper right on the back of the front panel board, see image.

In this way three things are achieved:

1. The amplified audio output is independent of the AF pot setting.
2. The zero-beat indicator is also independent of the audio pot setting.
3. The ‘no-wire’ philosophy of K2 is maintained, as there are no wires that need to be run to any of the other boards.

The schematic of the audio buffer and the updated zero-beat indicator is here. Note that the zero-beat indicator’s component values have some minor changes from the original design, that gave a nicer behavior of the display.

I also have added an optional signal from the sidetone circuit on the K2's control board (requires a plugable strap between the boards). This gives a visual check of the zero-beat indicator when you transmit, and it is also nice for demo purposes as both the received and the transmitted CW are output and can be decoded using e.g. a PC.

My Elecraft K2 Modifications

When I got my license in 2001, I discovered the Elecraft K2 transceiver on the internet and noticed the excellent reviews that it had received. Its receiver outperforms most, if not all, of the commercial rigs on the market. It combines state-of-the art performance with the thrill of building something yourself. It is also important for me that the kit designers encourage experimentation and modification.

My basic K2 with no options, serial #2198, was assembled in August 2001. I have later added the options that are needed to make all the front panel labels meaningful: the KSB2 single sideband option, KAT2 automatic antenna tuner, KAF2 audio filter and real-time clock, KNB2 noise blanker, and K160 160m/2nd RX antenna.

Morse lives on

Nice drawing of Bencher keyer by Dutch radio amateur
Dick Kraayveld, PA3ALM
(http://www.morsecode.nl/pa3alm.html)

Although morse has been more or less discontinued in a professional context, radio amateurs are active users of morse code. It gives me a kick every time I am able to receive and send morse code, something which a digital 'black box' never can give. The fact that morse has been replaced by satellites, internet and digital communications is as relevant as the replacement of horse transport by cars, sail boats by motor boats or bicycles by motor cycles. People still ride, sail and bike ... and use morse!

AT Sprint (the original)

Photo: LA8EKA

The AT Sprint is a very nice limited edition surface mount CW transceiver designed by KD1JV Steve Weber. The printed circuit board measures 85 by 54 mm. It was quite a challenge, but a fun one, to build! 

It was designed to be a rig of a size fit for camping. It covers the 40, 30, and 20 meter bands with plug-in modules. The whole transceiver fits in an Altoids tin and outputs about 4 W. The rig in the tin weighs about 85 grams. It uses a DDS - Direct Digital Synthesis - chip for the VFO, it has a superheterodyne receiver with a four-crystal filter, audio AGC, audio filter, and a very efficient class E output stage. It also has a built-in memory keyer and a morse code frequency annunciator. It can take any battery voltage between 5.5 and 13.8 Volts.

Mobile Phone Conversion

Several fellow hams in the Asker and Bærum district have converted Mobira (Nokia) MD50 or MD59 Talkman NMT-450 phones from 1985-1988 to the 70 cm band. LA7TM, Nicolai, has played a central role in the conversion, based on the work of Finnish hams who pioneered the conversion and made their experiences and their software available. We then made some changes to the software. These changes are now included in the official Finnish version.