My first 24 hours on WSPR

My first beacon on 30 m, a free-running Ultimate QRSS kit (no GPS) has now been running for a full 24 hours using the Weak Signal Propagation Reporter (WSPR) mode. The figure comes from the WSPRnet page.

With an output power of about 150 mW to an 80 m horizontal loop it has not been possible to reach beyond Europe so far. Perhaps this will happen in the future with better conditions and/or with some more output power.

Added 26.9.2012: I made it for the first time across the Atlantic!
Timestamp           Call       MHz         SNR Drift  Grid      Pwr Reporter   RGrid      km      az
2012-09-26 00:50, LA3ZA, 10.140262, -26,   -2,   JO59fu, 0.2, WB2EEE, FN21xh, 5852, 290

Altoids Projects

Press image for magnification

I like to build small electronics projects and like many others I have found the small Altoids tins to be excellent enclosures. 

These tins are inexpensive, well shielded, easy to work with, and least but not least they enable you to make experimental circuits that are sturdy enough that they can be reused later.

Pictured here is a collection of projects I have built over the years with the hope that  they may inspire others.

Noisy Designer Lamp

Herstal pendant lamp,
type 06

Some years ago I had this annoying noise that made listening for weak signals on several of the shortwave radio bands virtually impossible. In the end I was finally able to track down the noise source: Our beautiful Danish Herstal designer lamps in the kitchen. Actually it wasn't the lamps themselves, but the dimmable switch mode power supply that came with them.

After some years of always having to remember to turn them off, in the end I just replaced the original noisy dimmer with a fixed voltage, noiseless, electronic transformer and inserted lower wattage 12 V light bulbs in the two lamps.

The original dimmer came in its own nice conical designer housing and inside one finds a more ordinary plastic housing. And of course it is marked with the CE mark, thus indicating that it should be fine with respect to noise.

Fixing my Lithuanian oscilloscope

I visited Riga, Latvia with a youth group which we as a family were involved with in 1992, and there I stumbled upon a Soviet oscilloscope in a department store. It was from the neighboring country, Lithuania, and was manufactured in Vilnius, the capital. The markings say what I guess means "Made in the Soviet Union". At least it says CCCP in the upper right-hand corner. I remember these letters very well as all Soviet athletes used to have them on their backs.

The oscilloscope came with full documentation, even with a bilingual manual. I had grown fond of this oscilloscope as it was lightweight and simple to use once I had learned what the Russian markings meant. It is a typical instrument for TV-repair with a 7 MHz bandwidth.

Now after 20 years, I was therefore very sad when it malfunctioned. This was the time to test if the manual was helpful or not. The symptom was that the beam no longer could span the whole screen in the X-direction. Even with the Horizontal positioning all the way to the left one could barely see the beam.

I opened the bilingual manual only to discover that the two languages were Russian and Lithuanian!

Transformerless tube power supply

In 2012 bulky power transformers that work directly from the power grid at 50/60 Hz have mostly disappeared. My objective here is to modernize the power supply for a one-tube transmitter in the same way.

The circuit is based on an electronic transformer for LED or halogen lamps. Electronic transformers usually have a minimum power rating, below which they will not start. This one can tolerate a lower load than most and gives out 12 Volts for a load from less than 10 W and up to 60 W.

Nostalgia from LA3ZA in 1949

I wasn't even born when this LA3ZA QSL-card was issued in 1949. This is because I am second generation LA3ZA after my father. When the callsign was reissued to me in 2001 it had been inactive for 40 years or so.

I still have the Hallicrafters S40A receiver which my father used with a 2 W input homemade tube transmitter. The S40A (image below) was what introduced me to shortwave listening during the good conditions of the solar peak in the late sixties, despite its mediocre performance I would say.

Vertical antenna on a turf roof

A vertical wire antenna based on a MFJ-1904H 6.7 m (22 feet) telescopic fiberglass pole as shown here is easily tuneable for all bands from 40 m to 10 m. Here it is placed on top of a turf (sod) roof with quarter wave radials for all the 7 bands going to each of the two sides sloping down as they follow the contour of the roof. The antenna seems to work satisfactorily at least on the 30, 20, and 17 m bands which I have been able to test so far.

A turf roof is a traditional Scandinavian type of green roof covered with grass. It dates back to the Viking age and before. In modern times it has seen a renaissance in e.g. mountain cabins.

But how does the turf affect the antenna or to pose the question more precisely: Can it be used to improve the ground plane and the antenna's performance?

Vintage Tektronix oscilloscopes

I first encountered this generation of Tektronix oscilloscopes in my first job at the Electronics Lab of SINTEF, Trondheim, Norway in 1978. Already at that time the main use for them was as heaters in the offices. That is, only if you wanted to work in the break between Christmas and New Year when the central heating was turned down.

Since then I have come across the two oscilloscopes shown here, and the collector (or is it hoarder?) in me has not been able to say no to them. They are really advanced for their time: regulated power supplies with tubes, ceramic stand-offs and lots and lots of tubes.

The  oscilloscopes are 541A and 543, from 1959 and 1964 respectively, it seems. The plug-in units are 1A1, L, M, and 53/54K plus the cart. The 1A1 actually seems even to have FET-transistors, not only tubes like the others. The units work, but how well they work I am not sure about as they have been in storage for the last 5-10 years.